What is the Weight of the Fastway e2 Weight Distribution w/ 2-Point Sway Control

Question

Question:

Hello. I’m looking for a WDH. I am interested in the Fastway E2 800 with the round bars. Just wondering what the complete weight is for that? I am hoping to keep to weight down to not impact vehicle payload as much as possible. Please advise if you have a lighter weight WDH. Thanks

asked by: Braden

0

Expert Reply:

The Fastway e2 Weight Distribution w/ 2-Point Sway Control # FA94-00-0800 is going to be approximately 81 lbs. Looking through the weight distribution hitches that we have, I did not see another one of similar style that was lighter than the # FA94-00-0800.

It is also important to note that a weight distribution hitch does not count as tongue weight or get applied to the payload since it becomes a part of the hitch.

expert reply by: Scott S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What is the Weight of the Fastway e2 Weight Distribution w/ 2-Point Sway Control

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching