Mounting Brackets Installing Roadmaster Steering Stabilizer On 2010 Cambria RV E-450 Chassis

Question

Question:

I have a 2010 Itasca Cambrai 30 ft. Class C I am looking at Steering Stabilizer by roadmaster. could you help me to figure out which on to purchase. thank you ..

asked by: Tina K

0

Expert Reply:

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets # RM47MR is the correct kit for your 2010 Itasca Cambria.

expert reply by: Bud M

0

Answer 1

The install of the Roadmaster Exact Center Steering Stabilizer part #RM47MR does not require more than 150 ft lbs of torque. It's not a great idea to use a torque wrench as a breaker bar to loosen hardware. And I'm saying that as someone who…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 4

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 5

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 6

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The air suspension system on your 2022 Ram 2500 limits your options for suspension enhancement. None of the air bags made for your truck will be compatible. Instead, I recommend adding the SumoSprings Rebel Custom Helper Springs #SS64VR. The…

view full answer...

Answer 9

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I found the online version of the install instructions for the Exact Center stabilizers like the #RM47MR. What's fun is that just when you think you have found the correct step to address your problem it tells you to continue to the next step.…

view full answer...

Mounting Brackets Installing Roadmaster Steering Stabilizer On 2010 Cambria RV E-450 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching