Replacement Brackets for B&W Turnoverball Gooseneck Hitch GNRK1313 on Dodge Ram

Question

Question:

I need to order the frame rail for a b and w turn over ball they are about rusted out and I can’t really find them anywhere please help

asked by: Cody

0

Expert Reply:

It sounds like you're looking for the B&W Turnoverball Gooseneck Custom Installation Kit for Dodge part # BWGNRM1313 which is a replacement for the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1313 that fits Dodge Rams.

expert reply by: Conner L

0

Answer 1

The B&W Turnoverball Gooseneck Custom Installation Kit #BWGNRM1313 contains the mounting hardware and brackets for the Hitch #BWGNRK1313. It does not contain the Center Section #BWGNRC900 or Safety Chain U-Bolts #BW1900-2-1600. This is the…

view full answer...

Answer 2

I have some great news for you, as I reached out to the manufacturer, B&W, and they told me the 1303 center section is compatible! The older 1303 kit used Center Section #BWGNRC900, which is also the same center section for the newer…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

In regards to HappiJac Truck-Mounted Camper Tie-Downs like part #LC182908-182928, the front tie-down installs inside the bed on the front panel directly behind the cab. The rear tie-down then mounts to the bumper. They will not require removal of the…

view full answer...

Answer 9

Thanks for the pictures but no, the EX2700 tonneau cover that the #EX1700 fits is for a 2004-15 Nissan Titan 6' 7" Bed. The one previously mentioned #EX1770 is for your truck, so it'd for sure work if you have the 2770 tonneau cover.

view full answer...

Answer 10

Your air bag mounting location will determine compatibility with the Gooseneck trailer hitch #BWGNRK1313. The side plates of the gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail. See diagram to the right and video…

view full answer...

Answer 11

The side plates of the B&W gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail of your 2004 Dodge 2500 8-foot bed. See the B&W video I included at the 7 min and 30 second mark. If your Firestone air bags like…

view full answer...

Replacement Brackets for B&W Turnoverball Gooseneck Hitch GNRK1313 on Dodge Ram

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching