Distance Between the Arms at the Top of the V Shape on Jack-It 2 Bike Rack

Question

Question:

I have a long recumbent bike. How far apart are the tips of the V on the Jack-it bike rack?

asked by: Nancy A

1

Helpful Expert Reply:

The distance between the two arms that form the "V" shape at the widest point is 46-3/4". See the diagram below which shows all of the dimensions for the bike rack.

expert reply by: Robin H

1

Jack-It 2 Bike Rack Dimensions.
(click to enlarge)

Answer 1

The Jack-It 2 Bike Rack for A-Frame Trailers #LC429756 will be 29-3/16" tall when the top arms that hold the bikes are removed. As pop up campers are all different you will need to determine how far your bed area slides out and the height to…

view full answer...

Answer 2

I pulled up pictures of your 2012 Travel Lite Idea 15q and the Lippert Jack-It bike rack part #LC429756 would fit and work great.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Distance Between the Arms at the Top of the V Shape on Jack-It 2 Bike Rack

Featured Help Information

Miscellaneous Media

Continue Researching