Need Hydraulic Trailer Brake Kit for 1999 Demco Kar Kaddy Model KK360

Question

Question:

will these fit my kar kaddy? do I need 2 kits or does it replace both sides, and what is the fastest free shipping I can get

asked by: Roger

0

Expert Reply:

The Hydraulic Trailer Brake Kit, # AKUBRK-35 that you linked to is for a 10" diameter x 2-1/4" wide and for 4 bolt flange. It does appear that his will fit the application you are asking for, for the 1999 Demco Kar Kaddy Model KK360 with drum brakes. However, I will point out that we have the recommended replacement brake assemblies for the Demco Kar Kaddy in # DMSB24429M for the left side and # DMSB24428M for the right.

The # AKUBRK-35 is a good product but Demco does recommend the use of galvinized components and the # AKUBRK-35 is not. The Demco Hydraulic Drum Brake assembly # DMSB24429M for the left side and # DMSB24428M for the right, has a galvanized backing plate, stainless steel spring hardware and zinc-plated wheel cylinders. The self-adjusting brake does not require periodic manual adjustment like standard brakes and will not overadjust.

expert reply by: Michael R

0

Answer 1

We can certainly help you with that. You'll need the Right Wheel Cylinder Assembly, part #DMSB9776M and the Left Wheel Cylinder Assembly, part #DMSB9777M

view full answer...

Answer 2

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 8

The biggest difference between the servo styles that you'll notice is between free backing plates and the others. The free-backing plates will allow your trailer to back up without having the brakes lock up. With surge brakes typically when you…

view full answer...

Answer 9

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 10

Yes, if you inserted a rod into the hole that in front of the housing of the actuator of the part #DM72VR that would work as a manual lock out and allow you to reverse the trailer.

view full answer...

Need Hydraulic Trailer Brake Kit for 1999 Demco Kar Kaddy Model KK360

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching