Where Does Timbren Suspension Enhancement Install on a 2012 Toyota Tacoma

Question

Question:

How is the TTORTUN4 installed on a 2012 Toyota Tacoma, four door long bed, four wheel drive? Does it fit on the frame, or under the u-bolts as described for the Tundra? Look forward to your answer, thank you.

asked by: Lawrence W

1

Helpful Expert Reply:

The Timbren suspension system # TTORTUN4 installs directly over the center of the rear axle and leaf spring stack. Take a look at the picture I have included to see where it will go on your truck.

expert reply by: Michael H

1

click to enlarge

Answer 1

When installing any Timbren system on the 2019 Toyota Tacoma you should have about 1/2" to 1-1/2" between the frame and the spring after installation. You won't necessarily be losing wheel travel when you use a Timbren Rear…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Where Does Timbren Suspension Enhancement Install on a 2012 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching