Do You Have To Open Both Latches To Lift The Lid On UWS Toolbox # UWS07045?

Question

Question:

Do latches on both sides have to be pulled to open the lid?

asked by: Mike B

0

Expert Reply:

No, the latches on the UWS Low Profile Truck Bed Toolbox # UWS07045 are connected with a cross bar so you will only have to pull one latch on either side to open the toolbox.

There is only one lock on the drivers side of the box so if that is locked you will have to unlock the box from the drivers side.

expert reply by: Bud M

0

Answer 1

The UWS Low Profile Truck Bed Toolbox #UWS07044 and #UWS07045 have the same dimensions. The correct dimensions for both of these are 72" long x 12" wide x 17-1/4" tall with a capacity of 6.5 cu ft of usable space. The only…

view full answer...

Answer 2

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is…

view full answer...

Answer 3

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Answer 6

According to Torklift they recommend that the tension on a turnbuckle, like their TorkLift SpringLoad XL Turnbuckles for Frame-Mounted Camper Tie-Downs #TLS9050A should be at 300-ft/lbs to properly secure the camper. This is going to be standard…

view full answer...

Answer 7

Trailer tire and wheel combinations like the Provider ST205/75R15 Radial Trailer Tire w/ 15" Vesper Black Mod Wheel - 5 on 4-1/2 - LR D #MX47FR do not come fully balanced like a vehicle wheel and tire would be, and instead are mounted by…

view full answer...

Answer 8

The Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 10K GTW, 1K TW #C17062 is not available without the shank. For your raised truck, you can interchange companies for the shank head, however the companies may void your…

view full answer...

Answer 9

For your 2013 Ford F-250, the Timbren Rear Suspension System, part #TFR250SDG, should work just fine. These install in place of the factory installed bump stops so they should not interfere with the fifth wheel installation at all. These are…

view full answer...

Answer 10

Trailer ramp door springs are generally chosen based on the inside width of the trailer where it will be installed. Also, ramp door springs such as #362SA6 can be trimmed down some if the length is too much for the trailer. This is the shortest…

view full answer...

Answer 11

We don't have ability to cut down our trailer ramp springs at this time but we do have a Conventional Ramp Door Spring that does fit your 61 inch wide door that would not require cutting with the part #362SA6 which would work great.

view full answer...

Do You Have To Open Both Latches To Lift The Lid On UWS Toolbox # UWS07045?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching