What Hitch do You Recommend for My 1UP USA Quick Rack on My 2022 Toyota Camry?

Question

Question:

I have a 1Up USA quick rack for a 1-1/4" hitch. What hitch do I need that will work with the rack on my 2022 Toyota Camry?

asked by: Carlos

0

Expert Reply:

For the best route of hitch that is compatible with your 1UP USA Quick Rack with a 1-1/4" shank on your 2022 Toyota Camry, I recommend the Curt Hitch # C11576. This hitch comes with a 200 pound tongue weight and an outer gloss coat over the base powder coat that provides ultimate resistance from rust and corrosion.

Given the available specs of the Quick Rack, I unfortunately could not find the shank length of the rack. With that being said, even though we do not have the exact bumper clearance measurement for a 2022 model Camry, we do know that the measurement from the pinhole of the hitch to the fact of your rear bumper is 2 inches long. As long as the shank of the Quick Rack is longer, you will have no bumper clearance issue. The best way to confirm this is to measure from the center of the shank's pinhole to the closest part of the rack when folded in the up position.

expert reply by: Bob C

0

Answer 1

I have a great demonstration video that shows exactly what to do! Our expert Jon walks you through how to turn the bottom hooks of the FullBack 2 #Y02634 into the "anchor mode" at the attached video at timestamp 3:25. You simply flip the…

view full answer...

Answer 2

I do have a solution for you, however there isn't a 2" receiver available for your Toyota Camry. The Camry just does not have the capacity to match what a 2" receiver offers. You can use the Curt #C11576 1-1/4" Class-I hitch and…

view full answer...

Answer 3

Depending on your climate and how much salt your area ends up putting on the roads will great affect how quickly a hitch would get rusty. If you're up north in the "rust belt" it's very likely a hitch is going to develop surface…

view full answer...

Answer 4

Hitch rattle isn't a super common issue but there are some easy ways to relieve the noise. The easiest solution is to bend the exhaust hanger up so that the muffler sets further above the hitch. If bending the hanger does not provide a solution,…

view full answer...

Answer 5

While the Curt Trailer Hitch Receiver #C11576 you were looking at is confirmed to fit all models of the 2021 Toyota Camry including your 2021 Toyota Camry TRD, you may have to trim the middle section of the lower bumper if it sticks down any further…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C11576 on your 2019 Camry will fit. The double wall on that frame does make it a little tricky to get those bolts and plates into the correct position. I reached out to my tech contact at Curt who said you will need…

view full answer...

Answer 7

We have not heard any complaints or feedback regarding the Curt Trailer Hitch #C11576 rubbing against the exhaust of your 2019 Toyota Camry when installed. This particular hitch is a bit more concealed but both it and the Draw-Tite alternative…

view full answer...

Answer 8

For your 2018 Toyota Camry, we only have one hitch that will fit, it is the Curt Trailer Hitch Receiver part #C11576. It is not very visible which you can also see for yourself from the attached photo. Unfortunately, we have not yet installed the…

view full answer...

Answer 9

For your 2021 Toyota Camry LE Hybrid I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" Item #C11576. It is confirmed to fit all models, hybrid and non-hybrid, and has a 2,000lbs GTW and 200lbs TW capacity. This trailer…

view full answer...

Answer 10

For your 2020 Toyota Avalon Hybrid I highly recommend the Curt Trailer Hitch Receiver #C11576, which is confirmed to fit your Hybrid model and features a nice hidden crosstube design that allows only the 1-1/4" receiver to be visible behind the…

view full answer...

Answer 11

No, and there will never ever be a 2 inch hitch available for a 2018 Toyota Camry; the only option is indeed the 1-1/4 inch Curt Trailer Hitch #C11576.

view full answer...

Answer 12

I took a look at the installation video and instructions for the Curt Trailer Hitch Receiver item #C11576. It does look like you are going to have to do some trimming of the under panel to accommodate the receiver portion of the hitch and the lip for…

view full answer...