What Kind of Hardware is Needed to Install Lippert SolidStep # LC791572

Question

Question:

The description states that the installation hardware is not included. What installation hardware is required. Will this step fit my 2006 Forest River Georgetown 340st. Currently have an electric 3 step. My door is 26 inches wide and my steps are 24 inches wide

asked by: Ray M

0

Expert Reply:

To install the Lippert SolidStep # LC791572 you will need to use two #10, 1-1/2 inch self-tapping screws (for a laminate floor) or two #10 - 1-1/2 inch wood screws (for a wood floor). After they are installed you will check the alignment and functionality of the steps and make any adjustments.

Once that is done you will need 8 additional screws of the same type and size as used before to complete the installation of the steps.

expert reply by: Michael H

0

Answer 1

The bolt, or fastener screws, that come with the Replacement Hardware and Backer Plate for Lippert SolidStep Manual RV Steps #LC702580 are 10-24 x 4". This hardware is designed for Lippert SolidStep manual RV steps.

view full answer...

Answer 2

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 7

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 8

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 9

To replace the motor on the LCI Pump 650057 we have the Replacement Motor #LC167576.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

What Kind of Hardware is Needed to Install Lippert SolidStep # LC791572

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching