Does B and W Tow&Stow Adjustable Ball Mount Affect Turning Radius

Question

Question:

Does this cut your turning radius down? It looks like the balls on the side would get into your adjustable trailer tongue

asked by: Mark

0

Expert Reply:

The B&W Tow & Stow 3-Ball Mount # BWTS30048B that you referenced does not affect your turning radius. The balls that are on either side would be too low to cause any interference.

expert reply by: Jameson C

0

Answer 1

When it comes to an adjustable ball mount for your 2021 Ram 3500 with a 3 inch hitch The B&W Tow & Stow 3-Ball Mount - 3 inch Hitch - 4-1/2 inch Drop, 4 inch Rise - 21K - Black #BWTS30048B will work. The gross towing weight for the ball mount…

view full answer...

Answer 2

I would be happy to help you find the right ball mount for your husbands birthday. You are gong to need to measure the receiver on the end of his F-350 to determine the correct ball mount you need. You will want to measure the inside of the square.…

view full answer...

Answer 3

We do! The available kits are the B&W Tow & Stow 3-Ball Mount - 3" Hitch - 7-1/2" Drop, 7" Rise - 21K - Black #BWTS30049B and B&W Tow & Stow 3-Ball Mount - 3" Hitch - 4-1/2" Drop, 4" Rise - 21K - Black…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Does B and W Tow&Stow Adjustable Ball Mount Affect Turning Radius

Product Page this Question was Asked From

Continue Researching