Suspension Enhancement For A 2022 Kia Telluride

Question

Question:

DO you have any suspension enhancements for a 2022 Kia Telluride

asked by: Teresa

0

Expert Reply:

For your 2022 Kia Telluride, we do have an option for you. The Air Lift 1000 Air Helper Springs for Coil Springs # AL29PD will fit all models of the 2022 Kia Telluride and provides up to 1,000lbs of load leveling support, that will help reduce tire wear and OEM suspension strain.

This kit will help keep your vehicle level while hauling a heavy load as well.

expert reply by: Bryce D

0

Answer 1

The Air Lift AirLift 1000HD Air Helper Springs for Coil Springs part #AL60828HD is a confirmed fit for your 2019 Ram 1500. These can be helpful in eliminating a lot of the sag you are experiencing. Keep in mind these do not increase your capacity…

view full answer...

Answer 2

As your 2022 Hyundai Palisade is rated to tow up to 5,000 pounds and has a tongue weight capacity of 750 pounds, I recommend going with the etrailer.com #e95ZR. This matches your towing and tongue weight capacity exactly and will be a perfect fit…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...