What Front and Rear SumoSprings do You Recommend for My 2022 Ford E-350 Chassis?

Question

Question:

What front and rear sumosprings do you recommend for my 2022 thor class c motorhome on a ford e-series cutaway chassis e-350? I'm just looking for a little boost.

asked by: Mike T

0

Expert Reply:

For just a little boost on your front and rear suspension on your 2022 Thor Class c on a E-350 Cutaway chassis, I recommend the following setup:

- SumoSprings Solo Custom Helper Springs - Front Axle # SSF-106-40
- SumoSprings Maxim Custom Helper Springs - Rear Axle # SSR-106-40-1

With these two sets of SumoSprings, you will have a load-leveling of 500 pounds in the front and 3,000 pounds in the back. The great thing about both of these SumoSpring models is that they do not require any maintenance once installed on your vehicle. They also loosen and compress based on how much weight you are transporting. Lastly, it is good to know that both of these sets were made 100% in the U.S.A.

expert reply by: Bob C

0

Answer 1

This is a great question and one that can cause some confusion. SumoSprings capacity is determined by how much weight it takes to compress the spring down to 50% of its original body height, so a spring like the #SSF-106-40 will compress down to half…

view full answer...

Answer 2

I will start off by saying that the Replacement Bushing #RM-205381-00 is the direct replacement for the Roadmaster Polyurethane Bushing Kit for 1-3/8" Diameter, Factory Rear Anti-Sway #RM-4139-300. To further that, the Replacement Polyurethane…

view full answer...

Answer 3

To replace just the hat bushing for your Roadmaster End Link Kit #RM-590230-00 you will need the part #RM-205223-00. For the metal sleeve that the bushings install around you will need the part #RM-205501-00. Each of these will include one bushing or…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 10

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 11

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

What Front and Rear SumoSprings do You Recommend for My 2022 Ford E-350 Chassis?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching