Is There a Hand Rail Available for MORryde Flip Tread Steps

Question

Question:

Is there a handrail available for the Morryde Flip Tread RV entry step. If not do the body mount fit into the brackets of the existing folding rail?

asked by: Bill

0

Expert Reply:

MORryde does not offer a hand rail for the Flip Tread Steps like the part # MR42UR so you'd need to use a folding hand rail that attaches to the RV like with the Lend-A-Hand part # AM-533.

expert reply by: Jameson C

0

Answer 1

Since your Venture leg is the follow leg the repair kit is #LC146060. If you had the lead leg it would be #LC146059.

view full answer...

Answer 2

The internal parts (screw and nut) on your Venture landing gear are not available as replacement parts but we may have a replacement leg. We carry several legs that could potentially work. Lead: #LC119102 (outer tube is 29-1/2 inches overall) Follow:…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 9

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Answer 10

I'm pretty sure you are correct that the Coil SumoSprings Custom Helper Springs #CSS-1145R will fit your 2018 Toyota Highlander, however, we haven't had the chance to test this out and SuperSprings doesn't have this listed in their…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...