Wiring Diagram for Superwinch LT4000 ATV Winch

Question

Question:

I purchased an Lt4000 ATV winch with a remote control switch. Can I download the wuring diagram for both?

asked by: Patrick G

0

Expert Reply:

I'd be more than happy to help you out! Attached is a wiring diagram for the Superwinch LT4000 ATV Winch # SW1140220. We don't have the instructions available as a download, but when I reached out to my contact at Superwinch they were able to provide me with the image I mentioned.

expert reply by: Jon G

0

Wiring Diagram for Superwinch LT4000 ATV Winch
(click to enlarge)

Answer 1

We do have what you are looking for but it is our part number #6-190.

view full answer...

Answer 2

We do have the Dexter trailer hub and drum part #8-285-9UC3 which might work but you would need to verify a few things. This is an 8k oil-bath hub with a bolt pattern of 8 on 6-1/2 inches. The bearings it takes are 25580 Inner / 02475 Outer. You…

view full answer...

Answer 3

For starters, the correct replacement switch for the Superwinch LT2000 ATV Winch 1120210 is the Replacement Rocker Switch part #SW2320200. I have attached a wiring diagram of the correct switch for you below as well as the text from the manual.…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Wiring Diagram for Superwinch LT4000 ATV Winch

Product Page this Question was Asked From

Continue Researching