Availability of a Trailer Swivel Jack with 8 to 10 Inch Pneumatic Wheels

Question

Question:

Is there a trailer jack like this with a 8 - 10 pneumatic tire?

asked by: Bobby

1

Helpful Expert Reply:

All of the swivel trailer jacks that we carry that have wheels have plastic wheels with the exception of the Trailer Valet, # STC-V211. With this jack you also get a trailer mover. The jack has a tongue weight capacity of 500 pounds so if you need a higher capacity you would have to go with a model with a plastic wheel. I have linked all of the swivel jacks that have wheels.

expert reply by: Michael H

1

Answer 1

Most A-frame campers like your 2019 Aliner Classic off-road model will have a caster wheel tongue jack that uses a hard plastic wheel. There are no replacement pneumatic tires that will fit in place of that wheel but there is a specialty jack product…

view full answer...

Answer 2

I may have a solution for you, but we don't carry any true pneumatic wheels for swiveling trailer jacks-they're typically only going to be used on heavy duty trailer jacks and dollies like the Trailer Valet #STC-V211. With that said, you may…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...