Which Timbren Kit Fits 2003 Ford F-150 4x4 that is Lifted

Question

Question:

what rear timbren spring will i need for 2003 f150 crew cab 4x4 with a rough country 2leveling kit installed

asked by: James P

0

Expert Reply:

The correct Timbren kit you'd need for your 2003 Ford F-150 4x4 is the part # TFR1525HD that you referenced and since you have the two inch leveling kit as well you'd need the spacers # A25723-90AH00 as well. You'd need a total of 4 of these since you have a 2 inch lift that's on both sides of the truck axle.

expert reply by: Jameson C

0

Answer 1

Timbren Kit part #TFR1525HD is an adjustable kit as it comes with a removable 1 inch spacer. I pulled one of these from our warehouse and the spacer in the kit measures 6 inches from the bottom of the frame to the end of the rubber spring, and…

view full answer...

Answer 2

The best way to prevent a vehicle like your 2018 Toyota Tacoma from sagging is with the use of a weight distribution system. What happens when you tow is that weight gets transferred to the rear axle of your tow vehicle which causes it to sag. A…

view full answer...

Answer 3

Adding skid wheels to your open car trailer is indeed what I recommend to help prevent the trailer from dragging when going up a steep driveway. These are designed specifically for this very purpose and will work well. I recommend taking a look at…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...

Answer 11

Hey Don, good question and I checked directly with Air Lift for you and can confirm that so long as your 2024 Ram 2500 Rebel does NOT have the factory auto-leveling air suspension, the air bags you asked about are indeed a fit: - Air Lift LoadLifter…

view full answer...

Answer 12

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...