Replacement Rear Header End Plugs For a Tuxedo Lo Pro Soft Roll Up Tonneau Cover.

Question

Question:

I have a 1117655 replacement cover and need rear header end plugs and cant find a #. I have the front header plugs.

asked by: Philip H

0

Expert Reply:

I reached out to Truxedo who confirmed that you need the Replacement Rear Header End Plugs for TruXedo Lo Pro Soft Roll-up Tonneau Cover # TX1117467. They informed me that these are the replacement plugs for all the Lo Pro covers manufactured since 2008.

expert reply by: Bud M

0

Answer 1

Thanks for sending in the photos of the date code and serial number, that is the key to finding the proper replacement! We have added the replacement cover to the website for you, the part number for the replacement cover is #TR34FR

view full answer...

Answer 2

The Replacement Cover #TX1117655 is the correct fabric for the TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX578101 that you have on your 2006 Ford F-150 with the 6-1/2' bed.

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Answer 8

We only have the products listed on our website. I just double-checked to see if there was anything matching your descripton. The 4 microwave/convection/OTR ovens are all well over your 24" wide location. One of the smallest is the Furrion…

view full answer...

Answer 9

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 10

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Replacement Rear Header End Plugs For a Tuxedo Lo Pro Soft Roll Up Tonneau Cover.

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching