Mounting Pannel For Redarc Tow-Pro Brake Controller For 2020 Toyota 4Runner

Question

Question:

I am finding the Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob for my 2020 4Runner. Ive looked at both the 331tpsi007 and 002. neither list 2020 4runner as exact fit.

asked by: James N

0

Expert Reply:

Even though it isn't listed, the Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-002 has been reported as a fit for 2020 4Runners, so it will work for you.

expert reply by: Bryce D

0

Answer 1

Yes, when installing the knob for the Redarc Tow-Pro Liberty Brake Controller item #RED24FR you will want to remove any extra material behind the insert. I am happy the video was able to help you out. I have linked a couple of pictures from the…

view full answer...

Answer 2

Whether you are using the user controlled mode (manual mode) or the proportional mode on the Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR there is no need for a diode. The only other thing you would need to install the RedArc Tow-Pro…

view full answer...

Answer 3

The only differences between the factory pigtail and the Redarc Pigtail #RED49FR (Redarc part number TPH-021) will indeed be the external ground and a diode pre-installed on the red wire. There were a few issues with brake controller wiring in the…

view full answer...

Answer 4

We have just what you need! For your 2021 Toyota 4Runner I recommend the Mounting Panel #331-TPSI-002 which was designed specifically for your vehicle and will replace one of the blank switches on the left side of your steering wheel. This will…

view full answer...

Answer 5

Basically you'll use all of the wires in the diagram you sent a picture in of except the green. That circuit is an illumination circuit that would not be used. It's normally for controllers that have a backlit display that comes on…

view full answer...

Answer 6

The Toyota 4 Runner had a knock-out plug already present and then we simply added the Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob #331-TPSI-001 which measures 1-1/4 by 1 inch. There is also the option of using…

view full answer...

Answer 7

If you have a factory tow package you will need the following items to pair with your Redarc Tow-Pro Liberty Brake Controller - Proportional, part #RED24FR. The Plug-and-Play Wiring Harness for Redarc Tow-Pro Classic or Elite Trailer Brake…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Mounting Pannel For Redarc Tow-Pro Brake Controller For 2020 Toyota 4Runner

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching