How To Find Correct Replacement Axle for Forest River Surveyor

Question

Question:

Hi, do you sell axles to replace for my 2007 Forest River surveyor light. Has I believe 69 in or 70 in from Frame Center side to side. Im sorry I do not know the Hub measurement. Thank you

asked by: Jim V

0

Expert Reply:

I don't know what axle your trailer uses either unfortunately but if you can take a bit of time to measure the exact spring center length, hub face length, and note the weight capacity on the axle tag you can determine fit for yourself matching the above up with an option below such as the Dexter Trailer Axle Beam part # T3584F-8974 which has a 3,500 lb capacity and measures 89" at the hub face and 74" at the spring center.

expert reply by: Conner L

0

Answer 1

I reached out to my contact at Dexter and your current axle has a hub face to hub face measurement of 88.58" and a spring center to spring center measurement of 68" with an axle capacity of 3500lbs. The closest replacement option we…

view full answer...

Answer 2

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

How To Find Correct Replacement Axle for Forest River Surveyor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching