Aluminum Liger Trailer Wheel Valve Stem Opening Diameter

Question

Question:

I want to install a TPMS on my trailer. OEM TPMS systems use a .452 inch diameter valve stem sensor. What is the standard valve stem opening diameter on these rims?

asked by: Morgen F

0

Expert Reply:

The opening for the valve stem on the Aluminum Liger Trailer Wheel item # LH49FR is 0.625 inches.

expert reply by: Jerred H

0

Answer 1

Since wheels are rated to withstand the PSI rating of the tires that are meant to fit it you will need to look at the valve stem as that is the deciding factor for the PSI rating, since it would be the lowest rated component for the wheel. With the…

view full answer...

Answer 2

Yes, The Aluminum Liger Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Black #LH49FR you were looking at will clear the 12" Titan disc brake conversion on your 5200lb Dexter axle. 12" rotors like what you have are compatible with…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Answer 10

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 11

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Aluminum Liger Trailer Wheel Valve Stem Opening Diameter

Product Page this Question was Asked From

Continue Researching