Replacement Coupler Solution for Atwood Yoke Style Coupler with 15775 Part Number

Question

Question:

I need an Atwood coupler repair kit for a 1966 Arrow 5k camping trailer axle. its adjusted and locks, but the lock jumps up and off. Atwood 15775 is no only number Ive found. We use a two inch ball.

asked by: Russell W

0

Expert Reply:

The AT15775 part that you referenced was a replacement latch repair kit from Atwood for yoke style A-frame couplers. This kit is no longer available as Atwood was bought out and their parts were discontinued.

For a replacement yoke style coupler for 2 inch hitch balls, I recommend the etrailer.com # CA-5210-B. This is the same style of coupler that you have now.

expert reply by: Jameson C

0

Answer 1

Unfortunately we don't have a repair kit at this time. If you choose to replace the entire coupler, I recommend the Bulldog Collar-Lok Coupler w/ Low-Profile Latch - 2-5/16" Ball - A-Frame - 12,500 lbs #BD028499. For a bolt on…

view full answer...

Answer 2

Atwood was bought out and their replacement parts are no longer available - including the repair kit you mentioned - so the best option is to replace that A-frame coupler with a new one that attaches to a 2 inch hitch ball. There is a similar…

view full answer...

Answer 3

I do have an option for you but coupler repair parts aren't universal so if any of the internal latching mechanisms are damaged or worn on your trailer coupler then chances are high it will need to be replaced for which we offer the A-Frame…

view full answer...

Answer 4

We do not currently have a latch repair kit available for the A-Frame Trailer Coupler #CA-5210-B that you referenced. I also don't believe the same latch assembly from this unit would install on your existing Atwood model without…

view full answer...

Answer 5

There will be no trailer coupler latch repair kit for an Atwood Trailer Coupler 88555 which is discontinued. Unfortunately, the only option is a full replacement for which I recommend the Demco A-Frame Trailer Coupler part #DM14793-81. This coupler…

view full answer...

Answer 6

There may be a repair/rebuild kit that you can use for your Atwood coupler. The kits are model specific so if you are able to provide a model number of your coupler I can see what we have available. Generally with some older Atwood couplers they…

view full answer...

Answer 7

I took a look at our yoke-style coupler #CA-5210-B and there doesn't seem to be any type of adjustments that can be made for the coupler to sit more snug on the hitch ball. I would check to make sure that your coupler is cleaned out and free…

view full answer...

Answer 8

Unfortunately we do not carry the Atwood Yoke Coupler Repair kit any longer. Atwood was bought out and that kit was discontinued. I recommend replacing your coupler with the A-Frame Trailer Coupler - Yoke Latch - Black - 2" Ball - Weld On…

view full answer...

Answer 9

Since that Atwood coupler is a standard a-frame coupler you could use the Fulton part #F44314R0303 for a replacement that has a 2-5/16 inch hitch ball.

view full answer...

Answer 10

Unfortunately, Atwood no longer has the repair kits available. They were bought out and the company that now owns them stopped producing the repair parts you need. I recommend the A-Frame Trailer Coupler - Yoke Latch #CA-5210-B for your replacement…

view full answer...

Answer 11

I have a solution for you. We do not carry hardware kits for the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K #DM37ZR. However the instructions will give you the dimensions you will need and you can…

view full answer...

Answer 12

Yes, I would recommend keeping the bolts of the #AP233 lubricated. An easy way to do this is to use wet bolts like part #126B2 which have a zerk fitting that allows for easy application of grease to them.

view full answer...