Looking for Boat Trailer Clearance Light to Replace Signal Stat 1500

Question

Question:

I have a boat trailer equipped with Signal Stat 1500 clearance lights. Are the AL91RB direct replacements? Dimensions and mount appear to be compatable, but I didnt see the Signal Stat 1500 on your direct replacement list. Thanks

asked by: Bruce S

1

Helpful Expert Reply:

According to my Optronics representative, the # AL91RB marker/clearance light you mentioned is a direct replacement for the Truck-Lite 15 series. The Signal Stat 1500 is how Truck-Lite refers to the same lamp in its LED version.

A mounting bezel is available, part # A91BB for black or # A91CB for chrome plated ABS. If either one of these self-grounding bezels is used, use a # A91LW pigtail. If a non grounding bezel or bracket is used, a two wire pigtail like part # A46PB would be needed.

expert reply by: Mike L

1

Answer 1

For the clearance light part #AL91RB we have the grommet part #A91GB which is basically a hard rubber.

view full answer...

Answer 2

Yes, the Peterson LED Identification Light Bar #M191-3RL that you referenced would work great on your 2005 Nitro boat trailer as this is submersible and universal enough that it can easily be made to fit a boat trailer like yours.

view full answer...

Answer 3

What you can do is apply something like Liquid Electrical Tape, #SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical tape as well for extra protection.…

view full answer...

Answer 4

You bet we do! For the LED version, you'll need part #AL91RB. The lamp can be grommet mounted using #A91GB or surface mounted using a self grounding base like #A91BB for black/ #A91CB for chrome or a standard base like part #A91BOB for black/…

view full answer...

Answer 5

For the clearance light #AL91RB and the matching amber light you would install the lights in the appropriate bases like #A91BB and then use 2-wire pigtail #A46PB, plug it into the backs of the lights and attach the wires to the existing trailer…

view full answer...

Answer 6

The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this you'd need the part #A46PB and then for a grmmet part…

view full answer...

Answer 7

The Optronics Sealed Micro-Flex LED Trailer Side Marker #MCL50RB referenced in your question does have polarity, but the PL-10 Plug #A46PB that you also have is designed so that it can only be plugged in one way. This is essentially how you will know…

view full answer...

Answer 8

We don't have an exact replacement for the #STL37RB but we do have a replacement lens for the incandescent version of this light. For that you would need the part #A39RB.

view full answer...

Answer 9

If you are going to back your trailer in the water while it is still connected to the tow vehicle, you will need it to be waterproof. Whether or not it is water proof depends on the trailer, the construction, how it is wired, and if the taillight…

view full answer...

Answer 10

What you can do is apply something like Liquid Electrical Tape, #SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical tape as well for extra protection.…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...