Distance From Hitch Pin Hole To Ball Shank Center On a Curt TruTrack Weight Distribution # C17499

Question

Question:

Distance from center of pin hole to center of ball shank hole?

asked by: Dean

0

Expert Reply:

The Curt TruTrack Weight Distribution System # C17499 is going to be approximately 12" from the hitch pin center hole to the center of the ball shank hole. The exact measurement will vary between vehicles as the head of the hitch is adjustable for pitch making this measurement change depending on its adjustment.

If you are needing the hitch ball to be further away from your 2017 Ram ProMaster 2500 you can use the Equal-i-zer Weight Dist Shank # EQ90-02-4600 to gain an additional 6" from the included shank that comes with the TruTrack System.

expert reply by: Bud M

0

Curt TruTrack Weight Distribution System # C17499 Hitch Ball To Hitch Pin Measurement
(click to enlarge)

Equal-i-zer Weight Dist Shank # EQ90-02-4600 Dimensions
(click to enlarge)

Answer 1

When using the Curt TruTrack Weight Distribution System w/ Sway Control #C17499, which is a great system for your trailer weight and vehicle, you will initially setup your system just like you would a ball mount. So you will measure from level ground…

view full answer...

Answer 2

Yes, I went out into our warehouse to measure the nut of the Trailer Hitch Ball #C40030 and found that a 1-7/8 inch wrench would be the correct size. The same size wrench would be used for the top portion of the ball as well.

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Distance From Hitch Pin Hole To Ball Shank Center On a Curt TruTrack Weight Distribution # C17499

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching