Installing Flexco Manual Pull-Out Steps On A 2021 Winnebago Micro Minnie 1808FBS

Question

Question:

I received my steps and they do not fit. Will I need the outrigger to get these on? Please help.

asked by: Deb

0

Expert Reply:

The Flexco Manual Pull-Out Steps for RVs # SMFP-2100 were designed to fit a 26" mounting bracket width so if your older steps were a little big larger or wider you can definitely use the Lippert Outriggers for Manual RV Steps # LC301704 to help match these steps to your mounting plate bolt pattern.

expert reply by: Kevin C

0

Answer 1

Flexco Manual Pull-Out Steps for RVs - Double - 7-7/8" Drop/Rise - 24" Wide - 350 lbs #SMFP-2100 are from Stromberg-Carlson and are Flexco model steps. So in other words they are one in the same. I included some pictures showing dimensions…

view full answer...

Answer 2

The Flexco manual pull out step part #SMFP-2100 will fit your 2017 Keystone Springdale 179QB and most likely would just bolt right to the frame, but worst case scenario you would have to move some mounting brackets around. If you needed outriggers to…

view full answer...

Answer 3

Sounds like your trailer axles are a bit too short if the inner sidewall is rubbing on the frame of the trailer. Did you recently change to a wider tire? That could be the cause too. Your equalizer being angled shouldn't cause the issue you…

view full answer...

Answer 4

Yes, the Lippert Outriggers part #LC301704 are exactly what you described. These attach to the bottom of the trailer frame and provide brackets for the RV steps to attach to.

view full answer...

Answer 5

It sounds like you may not have power getting back to the camera. Start the truck. Check the plug on the truck to make sure you have power coming from all the pins except one. One will be ground. Have someone run through the functions on the truck…

view full answer...

Answer 6

I can absolutely help you out, but in order to find out exactly which steps Winnebago intended for your Micro Minnie 2306BHS to use, you'll want to measure the distance inside of your door frame and from the floor of the camper to the ground.…

view full answer...

Answer 7

The Furrion Vision S Wireless RV Backup Camera Systems; part #FOS43TASF for 4.3" screen or part #FOS05TASF for 5" screen, are going to be powered by either the running or backup light circuit. If you don't have the running or backup…

view full answer...

Answer 8

Step #SMFP-2100 is supposed to mount up to factory holes on the bottom of the frame or it can be welded to the frame. For nuts and bolts use #LC118155-72 if you don't already have some from the old steps. For welding the installation should be…

view full answer...

Answer 9

The closest RV step we offer to 27 inches in width is the Flexco triple step #SMFP-3200L that measures 27-1/8 inches in total width. You might need the outriggers part #LC301704 to move the brackets out to install the steps if yours is 27 inches…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Installing Flexco Manual Pull-Out Steps On A 2021 Winnebago Micro Minnie 1808FBS

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching