Is There Drilling Required to Install the Curt Front Hitch # C31068 on a 2012 Ford F150 Ecoboost

Question

Question:

Will this hitch mount on the front of my 2012 4x4 F150, V-6, eco boost w/o any holes having to be drilled?

asked by: Jerry

0

Expert Reply:

There is no drilling required to install the Curt Front hitch # C31068 on your 2012 Ford F150 with Ecoboost 4WD.

You will have to temporarily remove the front air dam. Check out the installation instructions I attached for this product also.

expert reply by: Jameson C

0

Answer 1

There is a front mounted hitch that is confirmed to fit your 2013 Ford F150 4WD with Ecoboost, part #65061. However, this hitch does not have the capacity for your trailer as it only has a tongue weight rating of 500 lbs so I cannot recommend it for…

view full answer...

Answer 2

If you look at the instructions I have linked for both the Curt front hitch #C31068 and Draw-Tite version #65061 you will see that they are both positioned in basically the same place on the 2013 Ford F-150. Both have 2 inch receivers and are rated…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Is There Drilling Required to Install the Curt Front Hitch # C31068 on a 2012 Ford F150 Ecoboost

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching