Diameter Mounting Bracket For Stromberg-Carlson RV Ladder Support Peg

Question

Question:

Can you tell me the hole diameter measurements of : I will need 4 of these brackets if they fit. How much are they? and dameter please

asked by: Lodie

0

Expert Reply:

The Replacement Ladder Support Peg for Stromberg Carlson RV Exterior Ladder, # 8535 has 1/4" diameter holes for mounting hardware.

expert reply by: Michael R

0

Diameter Mounting Bracket For Stromberg-Carlson RV Ladder Support Peg
(click to enlarge)

Answer 1

We have 2 ladder standoffs with square bases, the Replacement Stand-Off Brace for Surco Universal Exterior RV Ladders #SPN-416, and the Replacement Ladder Support Peg for Stromberg Carlson RV Exterior Ladder #8535 you referenced. They both have the…

view full answer...

Answer 2

The four included stand-offs in the Stromberg Carlson RV Exterior Ladder #LA-401 have fixed positions on the ladder. You can see this in the photo I linked for you which shows the stand-offs and the uprights where the stand-offs screw into place. We…

view full answer...

Answer 3

For additional stand-offs to use with the Ladder part #LA-401BA you would want the part #8535 which is a 5 inch support peg/stand off.

view full answer...

Answer 4

The Replacement Ladder Support Peg for Stromberg Carlson RV Exterior Ladder - Rectangular - 5" #8535 is the only replacement mounting part available. The manufacturer doesn't make just the mounting base plate as an independent replacement…

view full answer...

Answer 5

I am not sure which piece constitutes as a spacer in the Stromberg Carlson ladder #LA-401. It could be the stand-offs, the horizontal part that goes between the back outside wall of the RV and the ladder. If that is the part you are looking for it is…

view full answer...

Answer 6

I may have an alternative solution for you, but we do not carry any ladders made by Christianson. We do carry the Stromberg Carlson RV Exterior Ladder w/ Hinges, part #LA-401 for Silver or part #LA-401BA for Black, which is a universal fit ladder. It…

view full answer...

Answer 7

Most RV ladders are actually supported by the rear wall and not the bumper actually. For example, if you take a look at the picture of the #LA-401 that you referenced you can see that it does not attach to a bumper at all and only the rear wall and…

view full answer...

Answer 8

I went out into our warehouse and measured the Replacement Ladder Support Peg #8535 and found that it measures 4-7/8 inches from the base to the black portion of the peg. If you could come up with a spacer that's a little bit wider than 1/2 of an…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Diameter Mounting Bracket For Stromberg-Carlson RV Ladder Support Peg

Product Page this Question was Asked From

Continue Researching