Will The Curt C17507 Replace The Head On An Older 17342 Weight Distribution System

Question

Question:

Hi. It appears Curt 17507 will replace 17342 well. Correct? I still have the 1000lb bars, 10k Convert a Ball cushioned 10k shank, and 15k Curt 2 5/16 ball. The head tilt spacers and adjustment holes in the head of our 17342 [2017 yr model] have worn to oblong shapes and thus loose. See attached pics. Not sure why as our loaded horse trailer is about 7k total weight. Suggestions? Thanks.

asked by: Lennie B

1

Helpful Expert Reply:

As the Curt C17342 weight distribution system was discontinued at the end of 2016, there will be no more direct replacement parts available for it, unfortunately. However, The bars that fit the Curt replacement head # C17507 will be a 1-5/16" square, so as long as your bars match this, it shouldn't be a problem.

The head tilt spacers do wear out over time, so it is completely normal. To get those replaced, the Replacement Hardware Kit for Curt TruTrack Weight Distribution System w/ Sway Control - 5K to 10K # C17550 will include these spacers as well as all the hardware needed for the head.

expert reply by: Lazer S

1

Curt Head Tilt Spacer
(click to enlarge)

Older Curt 17342 Head
(click to enlarge)

Answer 1

Thank you for the photos of your Curt weight distribution system! I'm not sure what that number on the sticker means, but from the pics you sent in that looks to be a TruTrack system like what we see with part #C17499. Unfortunately Curt…

view full answer...

Answer 2

Given the information you provided, your trailer's fully loaded tongue weight would likely range between 500 and 700 or so pounds. Since your travel trailer weighs more than 1/2 the weight of the travel trailer you'll wanting to tow,…

view full answer...

Answer 3

That foot pound rating for torqueing a hitch ball onto a ball mount requires a special torque wrench. A local mechanic should have something compatible. If you can't find anyone with the correct torque wrench as many max out at 250 lbs, then we…

view full answer...

Answer 4

Since you are seeing the electrical overload only when pressing the manual override, it sounds like your vehicle wiring is supplying more than 12V power to the Echo #C51180. If this is only happening when you use the manual override, then goes back…

view full answer...

Answer 5

I can give you a list of parts below that will be needed to rewire a trailer which you can then use when combined with the labor rate of the shop to give you an estimate but it can be very hard to estimate the price of said job because the labor…

view full answer...

Answer 6

The difference between the Curt TruTrack #C17501 and #C17499 are their weight capacities and the #C17501 comes with a 2-5/16" hitch ball already installed, whereas the #C17499 would require you to purchase one and torque it down yourself. The…

view full answer...

Answer 7

The max trailer weight that the Curt head part #C17075 can tow is 14,000 lbs and the max tongue weight is 1,400 lbs.

view full answer...

Answer 8

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 9

The MORryde Rubber Equalizers for Tandem Axle Trailers - 33" Wheelbase - 8K item #MR87ZR do come as a pair and you will be able to verify the cost on the product page.

view full answer...

Will The Curt C17507 Replace The Head On An Older 17342 Weight Distribution System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching