Furrion Vision S Wireless RV Observation Camera System Installed on the inTech Sol Horizon Rover

Question

Question:

Just purchased 2022 Intech Sol Horizon. Does this fit and install easily. Is drilling required? Probably will use installer anyway.

asked by: David A

0

Expert Reply:

Yes, you can fit the Furrion Vision S Wireless RV Observation Camera System, # FCE48TASL-05 to your 2022 inTech Sol Horizon Rover. While some RV OEM's have begun releasing their RV's from the factory with pre-wired mounts for back up cameras I am not aware of Sol doing so with the inTech. There will most likely be a need to drill hole(s) for mounting the back camera of this system. If you are hesitant about drilling holes in your new camper then yes, I suggest having this done by a professional installer.

expert reply by: Michael R

0

Answer 1

This is a great question and typically travel trailers will have electric brakes so you won't need to worry about them engaging when operating the Trailer Valet XL #TVXL25 since the trailer shouldn't be plugged into anything during this…

view full answer...

Answer 2

We do offer replacement parts for your Sears X-Cargo 20-SV rooftop cargo box. For a set of 2 locks and 2 keys you can use part #SR03807. This will work if the locks look the same. There is a lock nut on the back of the lock assembly that will need to…

view full answer...

Answer 3

Since you are needing a replacement lock as well as the key, you can use the Replacement Lock Core and Key #SR03807 for your Sears X-Cargo Sport 20 cargo box.

view full answer...

Answer 4

Since you mention you do not have the hook type lock like #SR03807 then this is likely to be the part you need. According to my contact at Thule, who made the SV cargo boxes for Sears, the complete replacement lock assembly like yours is not…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The brake controller port on a 2021 Ford F-150 (if equipped) will be located behind the coin tray in the center console. This will be accessed by removing the panel under the steering wheel. I have attached a video which shows this below. For a brake…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...