Pin Hole Dimensions In B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200

Question

Question:

My two set bolts are on the back of the coupling. Doni srill 2 new goes 9n the side of the coupling same height and align with the hitch. What size are the hole diameters exactly in the hitch?

asked by: Ryan

0

Expert Reply:

The pin holes in the B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200 are 3/4" in diameter for a 3/4" Pin # BD0233060301. The 8 holes are spaced 1" on center vertically for 8" range adjustment.

expert reply by: Bud M

0

Locking Pin Holes For B&W Extend-A-Gooseneck Coupler # BWTEXA4200
(click to enlarge)

Answer 1

The loft on your gooseneck horse trailer will be included in the length measurement. Basically, you will need to measure from the longest two points on the trailer (see photo). However, the longest storage cover we have for a gooseneck horse trailer…

view full answer...

Answer 2

I've attached a picture with three different measurements for the B&W Extend-A-Goose Gooseneck Coupler - 2-5/16" Ball - 10" Offset, #BWTEXA4200. It is 12 inches from the base or bottom of the coupler to the center of the lowest pin…

view full answer...

Answer 3

The B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200 will provide 10-inches of offset for better clearance between the truck and trailer. It sounds like you are using a B&W Offset ball like #BWGNXA4085 which gives you 4-inches of offset. It…

view full answer...

Answer 4

In regards to the B&W Extend-A-Goose Gooseneck Coupler part #BWTEXA4200, the distance from the bend in the upright to the bottom of the coupler is right at 9". I went out to our warehouse to measure this for you and created a diagram as…

view full answer...

Answer 5

I spoke with B&W and they said you are able to use the B&W Extend-A-Gooseneck Coupler #BWTEXA4200 in a reverse offset position.

view full answer...

Answer 6

I called my contact at B&W about the Extend-A-Goose Gooseneck Coupler, part #BWTEXA4200. They told me that the offset holes are so that the adapter can accommodate couplers that have the pin in different locations, and will not affect the towing…

view full answer...

Answer 7

For your 1993 Dodge Cab and Chassis with 10 foot bed, the distance from the hitch ball to the back of the bed needed would depend on your trailer as they are all slightly different. You would need to measure from the center of the ball to the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Pin Hole Dimensions In B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching