TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box Dimensions

Question

Question:

Hi, I was looking at the TLA7732 for a 2017 Chevy 2500 HD crew cab long bed truck for our inverter system. I cant seem to locate the dimensions to know if our existing sealed batteries will fit or not. Can you tell me the maximum size for a sealed deep cycle battery? And I presume more than one of these boxes can be installed one on each side or side by side

asked by: JOSH

0

Expert Reply:

The length of the TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box # TLA7732 lid measures 17-1/2 inches at its widest point, width is 9-3/4 inches at its furthest point and the height is 3-3/8 inches.

The overall length of the battery box is 15 inches not including the handles and including the handles on the sides is 17 inches. The width is 8-1/8 inches and the height is 8-1/2 inches.

This battery box will fit group 31 batteries which are approximately 13 long, 6 13/16 wide, 9 7/16 inches tall, and group 24 batteries which are approximately 11 inches long, by 6.875 inches wide, by 9.5 inches tall.

These can be installed next to each other or side by side.

expert reply by: Bryce D

0

Battery Box Dimensions
(click to enlarge)

Answer 1

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

Your 2008 Chevy HHR should have a set of rails on the roof that run from front to back. Which means we have the Rhino Rack part numbers #RRVA106B-2 and #RRSX100 as a confirmed fit, but the kit you mentioned is not a fit.

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box Dimensions

Product Page this Question was Asked From

Continue Researching