Recommended Truck bed Tool Box For A Ford F-250 Super Duty With BAKFlip Tonneau Cover

Question

Question:

Will this toolbox work with a bakflip cover?

asked by: Matt R

0

Expert Reply:

BAKFlip tonneau covers are going to interfere with opening the lid of the UWS Truck Bed Chest - Wedge Series - Offset Lid - Notched Box # UWS01048. Instead you can use a toolbox like the UWS Truck Bed Chest # UWS08297 or the # UWS08298 for black.

expert reply by: Kevin C

0

Answer 1

I attached a picture that has all of the available positions you can use for varying heights with the B and W Companion hitch part #BWRVK3305. It's best to measure first to determine which height you'd need, but if not then I'd go with…

view full answer...

Answer 2

Hello, I have attached a help article and an installation video that will hopefully assist in needed measurements to make the installation a smooth process. Happy Camping.

view full answer...

Answer 3

The BAKBox 2 Collapsible Truck Bed Toolbox for BAK Roll-X and BAKFlip Tonneau Covers #BAK92321 has not been tested for compatibility with the REV brand tonneau. The BAK rails have a specific channel for that box to fit which you can see in the…

view full answer...

Answer 4

We do carry the UWS Truck Bed Toolbox - 5th Wheel Series Chests in Black #UWS01066 and Polished Aluminum #UWS01042 which are specifically designed to work with 5th wheel hitches. Both are confirmed to fit your 2021 Ford F-350 Super Cab 4x4 dually…

view full answer...

Answer 5

For your 2022 Ford F-250 we have the UWS tool box part #UWS01048 for a black box or the part #UWS01040 for bright aluminum that are a confirmed fit and are shorter than the bed rail height of your truck so your tonneau would be able to close over…

view full answer...

Answer 6

When people install truck bed tool boxes like the part #UWS08298 in the bed of trucks like your Tacoma normally holes are drilled through the floor of the box and the truck bed and hardware is ran through both which secures it. We have this as an…

view full answer...

Answer 7

I have a possible solution for you. Unfortunately, I confirmed with my contact at Curt (the maker of UWS boxes) that the UWS Truck Bed Chest - Wedge Series - Offset Lid - Notched Box #UWS01048 is not available in a gauge higher than 0.63. This…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 12

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Recommended Truck bed Tool Box For A Ford F-250 Super Duty With BAKFlip Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching