Distance from Pin Hole to Flared Stops of Curt Hitch Adapter # C45405

Question

Question:

What is the dimension from the hole center to flared stops?

asked by: Randy B

1

Helpful Expert Reply:

The distance from the center of the hitch pin hole of the # C45405 to the flared stops is 2-5/8 inches.

expert reply by: Jameson C

1

Length Dimension
(click to enlarge)

Answer 1

The Timbren TFRTT350J will measure 7" from the top of the bracket to the bottom of the rubber spring/jounce. With you having 8-1/2" of space on your 2022 Ford F-250 Super Duty, you will have a 1-1/2" gap between the bottom of the…

view full answer...

Answer 2

For a single replacement Pin Lock you will need part #TL11001. It is a direct replacement for your pin lock with the key P01. My contact at TorkLift verified that all of them are keyed alike so you will not have to give any specific part numbers when…

view full answer...

Answer 3

The Torklift Locking FastGun Turnbuckles #TLS9529-2-LK which have a reach range of 25" - 43" would fit and work well for your 2018 Ford F-150 and Palomino Pop-up Camper SS-1251.

view full answer...

Answer 4

Yes. You can use the Blue Ox Sway Pro #BLU77FR on your 2010 GMC Sierra 2500 HD with the 2-1/2" hitch with the factory sleeve reducer. You could also use the Blue Ox Hitch Reducer Sleeve - 2-1/2" to 2" Trailer Hitch #BX88187 to…

view full answer...

Answer 5

There is no problem using a 2-1/2" to 2" Receiver Reducer Sleeve #e26YR with a weight distribution hitch. This way you will not need to replace your Shank #C17132 unless you have a significantly taller receiver on your new 3/4 ton truck.…

view full answer...

Answer 6

On a single axle trailer you will want to have a hanger spacing of around 22-3/4 inches when using the 23-1/8 inch long Double-Eye Spring #e59SR. This will allow that rear shackle to correctly lean away from the axle for proper suspension travel.

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…

view full answer...

Answer 9

So I have your hub narrowed down to a few different possibilities but we need to know what your bolt pattern is to know for sure. We have the part #84556UC3 for if your bolt pattern is 5 on 5 inch. We have the part #845476UC3 for if your bolt pattern…

view full answer...

Answer 10

The trick here is to get as close as possible. If you are talking about less than 2 inches or so, there is nothing to worry about. Having the trailer tongue a bit too high is preferable to it being too low. You may be a good candidate for an…

view full answer...

Answer 11

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 12

The Dometic 310 Part-Timer RV Toilet, #DOM37FR that you currently have, in tan, is a standard-height RV toilet with a ceramic bowl and slow-close lid. It is 20" tall with a seat length of 15-1/4" and seat cutout dimensions of 10-3/4"…

view full answer...

Distance from Pin Hole to Flared Stops of Curt Hitch Adapter # C45405

Product Page this Question was Asked From

Continue Researching