Can I Mount The Replacement Switch For The Automatic Battery Disconnect In The Wheel Well

Question

Question:

Is the button with this kit weatherproof, I would like to mount it in forward edge of wheelwell so I cant accidentally lock myself out with battery off and button inside while flat towing.

asked by: Bill M

0

Expert Reply:

The Replacement Switch for Roadmaster Automatic Battery Disconnect, part # RM57ZR, is not weatherproof. One of the installation requirements of the Roadmaster Automatic Battery Disconnect with Switch for Towed Vehicle w/ Supplemental Braking System, part # RM-766, is that it needs to be protected from direct road spray. In my opinion, the wheel well would provide too much spray and the switch and/or solenoid would get wet.

I have included a product description link, a video demo, and a copy of the Roadmaster Automatic Battery Disconnect instructions below.

expert reply by: Mark Smith

0

Battery Disconnect Installation Instructions
(click to enlarge)

Answer 1

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 2

The Battery Disconnect part #RM-766 installs on the positive battery wire so that when activated all power is cut for the vehicle. See attached chart. What you would need to do is install the #RM-766 after the connection you have for your Brake…

view full answer...

Answer 3

The process to install the Roadmaster Automatic Battery Disconnect part #RM-766 on your 2019 Chevrolet Silverado 1500 is a bit different than most like the ones you were referring to on our site however it can still be done. I have attached for you…

view full answer...

Answer 4

I would be happy to confirm the parts you referenced fit your 2019 Chevy Colorado and are compatible together. I have listed them below, along with any changes, and attached installation videos. Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 7

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 8

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...