Can Curt Echo Mobile Brake Controller be Installed in Vertical Orientation

Question

Question:

Can it be installed in a vertical instead of horizontal position?

asked by: Thomas B

0

Expert Reply:

Yes, the Curt Echo Mobile part # C51180 that you referenced can be installed in a vertical position. It can be installed in basically any orientation actually.

expert reply by: Jameson C

0

Answer 1

You should change your breaker to a 30 amp breaker when installing the Curt Echo Mobile #C51180. 40 amps is good for protecting more than two axles but if you have a tandem axle trailer you'd want the breaker to trip at draws above 30 amps so…

view full answer...

Answer 2

There's only one hitch for your 2022 Subaru Outback with that high of a tongue weight capacity and it is the Draw-Tite Trailer Hitch item #DT73RR. This hitch is custom fit and bolts to your Subaru with included hardware. It has a 4,500 lbs towing…

view full answer...

Answer 3

The Tekonsha Prodigy RF Wireless Trailer Brake Controller part #90250 must be mounted with 5 degrees of level on a horizontal plane lined up with towards the tow vehicle for the internal sensor to work properly. The sensor will not function if the…

view full answer...

Answer 4

The trailer brake controller I highly recommend for a 2019 Subaru Outback is the Curt Echo Wireless Trailer Brake Controller part #C51180 which does not require any splicing or drilling into the dash. It will require the Hopkins Plug-In Simple…

view full answer...

Answer 5

By far the best suspension enhancement for your 2021 Toyota Sienna are air helper springs: - Firestone Coil-Rite Air Helper Springs #F4155 The reason the Coil-Rite #F4155 are the best is due to the amount of additional support they add directly to…

view full answer...

Answer 6

A 12V trailer power circuit will typically be wired with 12-gauge wire, part #12-1-1, but certainly there is no harm in using heavier 10-gauge wire #10-1-1. If one tow vehicle is longer than another, our installers may opt to use the heavier gauge…

view full answer...

Answer 7

When your trailer is connected to a 7-way like the Pollak Metal 7-Pole, RV-Style Trailer Socket - Vehicle End #PK12703 the pin at the 1 o'clock position is the 12V power that will charge your trailer battery when it is connected to the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 12

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Can Curt Echo Mobile Brake Controller be Installed in Vertical Orientation

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching