Pin Hole to Ball Hole Dimension of B&W Ball Mount BWBMHD30011

Question

Question:

What is the distance between the pin and ball holes?

asked by: Tom G

0

Expert Reply:

The distance between the hitch pin hole and the hitch ball hole of the B and W Heavy Duty Ball Mount part # BWBMHD30011 that you referenced measures 10-1/4 inches.

expert reply by: Jameson C

0

Answer 1

Longer ball mounts are helpful for creating clearance from the rear of the vehicle to allow you to lower your tailgate while towing and not interfere with a tongue mounted jack or install hitch mounted accessories (like bike racks) that may require…

view full answer...

Answer 2

The closest ball mount we have to the Curt #C45340 that is USA made is the B and W Heavy Duty Ball Mount part #BWBMHD30011 which has the same 2 inch drop, has a 16k capacity, and fits a 2 inch hitch. We try to list on our product descriptions when…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Pin Hole to Ball Hole Dimension of B&W Ball Mount BWBMHD30011

Product Page this Question was Asked From

Continue Researching