Anti-Sway Bar For 2007 Roadtrek 210 Popular Motorhome

Question

Question:

Hi, I own a 2007 Roadtrek 210 Popular motorhome. The unit has a generator installed underneath just behind the rear differential. Are there any similar installs that you can share to determine the clearance required behind the differential? Pictures, dimensions, measurements would be helpful along with which sway bar might fit. Thank you

asked by: Richard W

0

Expert Reply:

If your motorhome has a generator mounted underneath your veicle behind the rear differential more than likely you are not going to be able to install a sway bar kit like # RM-1109-175-00 due to the generator being mounted where your sway bar would go leaving no room.

I contacted Roadmaster and they mentioned you should measure from the back of the differential to the edge of the generator, and if you have at least 10" of clearance your vehicle will work with # RM-1109-175-00.

expert reply by: Bryce D

0

Answer 1

According to my contact at Roadmaster, the Roadmaster Rear Anti-Sway Bar, #RM-1109-150, will fit a Class B motor home built on a Chevrolet Express 3500 Chassis such as your 2006 Pleasure-Way Lexor, but the size and the location of the generator will…

view full answer...

Answer 2

I spoke with a Roadmaster technician to verify the correct fit for your 1999 Chevy Roadtrek 200 Popular and found that the Roadmaster Rear Anti-Sway Bar and Axle Mounting Kit #RM-1109-150-00 is the correct fit. The brackets will attach to the outside…

view full answer...

Answer 3

For your 2010 RoadTrek 190, I recommend the Roadmaster Rear Anti-Sway Bar for Trucks and Motor Homes #RM-1109-175 which is a confirmed fit for your vehicle and should not interfere with your generator. I've attached an installation video to…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Anti-Sway Bar For 2007 Roadtrek 210 Popular Motorhome

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching