Availability Of Lift Kit For 2011 Jayco Jay Feather Ultra Lift W/ # 10 Dexter Torflex Axle

Question

Question:

Do you guys have a lift kit that is bigger then 2 5/8?this trailer has no clearance and Im replacing Jacks all the time.

asked by: Lance A

0

Expert Reply:

Since your 2011 Jayco Jay Feather Ultra Lite X17Z has a # 10 Dexter Torflex axle the only lift kit available for it is the # K71-707-01 is the correct lift kit, and its 2-5/8" lift is the most that is available for your trailer.

If this is not enough lift then reply back with the dimensions of your current jacks and I would be happy to find a shorter jack for you.

I included a video of the # K71-707-01 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The Expert question you are referring to is actually fairly old and the diagram for the Firestone Ride-Rite Air Helper Springs #F2430 that fit your 2014 GMC Sierra 1500 was updated to the bracket change that Firestone initiated for this kit. I have…

view full answer...

Answer 2

Thank you for providing that picture. Since you have a 3,500 lb torsion axle we know it is a Dexter #10 Torflex. This means the #K71-707-01 is indeed the correct lift kit for your trailer.

view full answer...

Answer 3

The axle number you gave appears to be either a #10 or #11 Torflex Axle. You can confirm this by checking the bolts where it meets your frame and they will be 8 inches on center. If this is the case then you will use lift kit #K71-707-01. If instead…

view full answer...

Answer 4

For your Dura-Flex 4,300 lb axle, we don't have a confirmed fit lift. If you axle mounting holes are 8 inches on center you can use #K71-707-01 to gain a 2-5/8 inch lift. This is rated for Dexter Torflex Axles up to 4,000 lbs capacity, so the…

view full answer...

Answer 5

On the Torflex Lift Kit #K71-707-01 the distance from the center of one bolt hole to the center of the other hole is 8 inches. The overall length is approximately 9-3/4 inches. I have linked a video of this product for you as well.

view full answer...

Answer 6

For your 2003 Sun Valley RoadRunner travel trailer, the #10 torflex axle will use lift kit #K71-707-01 if your axle is rated for 2,300 to 4,000 lbs. If you have a #9 Torflex axle with 2,000 lb capacity then you will want #K71-723-01. We also tandem…

view full answer...

Answer 7

The Torflex Lift Kit part #K71-707-01 is made from 7 gauge steel which is 3/16 inch thick. I attached a review video for this for you to check out as well for more info.

view full answer...

Answer 8

The Torflex axles have different axle capacities. For capacities between 2,200 lbs and 4,000 lbs you will have #10 Torflex axles. The mounting hardware witll be 8 inches on center so you will use lift kit #K71-707-01. Dexter doesn't give a number…

view full answer...

Answer 9

The only lift kit that Dexter Axle offers for your Torflex #11 axle, for whatever reason, is the Tandem Axle Kit #K71-724-02. We've double checked with Dexter directly a few different times and this is just what they sell. With this being the…

view full answer...

Answer 10

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 11

The Dexter Torflex Lift Kit #K71-707-02 referenced in your question is designed for the #10 Torflex axle with a 2,300 to 4,000 pound capacity. As you mentioned, the lift kit cannot be used with Torflex axles that use a 3 inch high profile bracket.…

view full answer...

Answer 12

The Dexter Axle Torflex axles are basically broken up into the following categories: #9 - 1,000 - 2,200 lb #10 - 2,300 - 4,000 lb #11 - 4,100 - 6,000 lb #12 - 5,500 - 7,200 lb Based off of your 2004 R-Vision Trail-Lite Model 8306S being a tandem axle…

view full answer...