Finding Correct Replacement Adjuster Spring For Dexter Electric Brake Assembly

Question

Question:

Will this work on a 1971 holiday rambler travel trailer its hard for me to tell but looks like it will this pic is the one that came off of it

asked by: Arlene W

0

Expert Reply:

It looks like you need Replacement Adjuster Spring for Dexter Electric Brake Assembly # BP08-155, but you can measure to verify. This measures 4.14" long and .43" wide. You may need to bend your old spring back in order to get an accurate measurement.

expert reply by: Andrew N

0

Old Spring For Brake Assembly
(click to enlarge)

Answer 1

I went to our warehouse to measure the Replacement Adjuster Spring for Dexter Electric Brake Assembly #BP08-155 for you. The length of the spring is 4.14 inches and the width is .43 inches. I've attached a photo to assist.

view full answer...

Answer 2

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 3

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 4

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

The Champion 9,000-Watt Dual Fuel Inverter Generators w/ Parallel Kit, #CH49FR has the same power output specs regardless of type fuel used. There is a starting (surge) power output of 4,500 watts/37.50 amps with a running power output of 3,500…

view full answer...

Answer 8

The Champion 9,000-Watt Dual Fuel Inverter Generators w/ Parallel Kit, #CH49FR have a push button electric start and operate from either propane or a minimum 87 octane rating gasoline for their fuel source. Run time is up to 14 hours on gas and as…

view full answer...

Answer 9

I recommend you only consider an inverter type generator. From the specs available to me online, your 2019 Forest River Salem 30KQBSS Travel Trailer is a 50-Amp service with 2nd A/C Prep option. If you have have the second AC unit installed or a…

view full answer...

Answer 10

It's good to know the Redline 2-Way Pop-Up Roof Vent #9106-2756 is finally back in style! :) There really isn't a "wrong" way to install it on a trailer but if it's raining you'd most likely want to keep it closed, or at the…

view full answer...

Answer 11

Since you have 3,500 lb axles you'd want a bearing kit for this axle capacity and not a 7k axle as the bearings and seals are totally different. For a 3,500 lb axle you'd want the part #BK2-100 instead. This comes with the correct size seal…

view full answer...

Answer 12

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Finding Correct Replacement Adjuster Spring For Dexter Electric Brake Assembly

Product Page this Question was Asked From

Continue Researching