How Many Crossbars Does a Yakima Fit Kit Work With

Question

Question:

I see it comes in a quantity of 2, so I’m assuming that’s 2 for 1 crossbar? I would need to purchase 2 kits to work with both crossbars?

asked by: Mike

0

Expert Reply:

You are correct the Yakima Fit Kits like part # Y79QR are sold in pairs or a single crossbar. So to do a setup that includes both crossbars you'd need a quantity of 2 fit kits.

expert reply by: Jameson C

0

Answer 1

I can do you one better, and instead of an exact match, I can get you the Yakima Base Clip 200, which is the following part number: - BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers #Y79QR I did verify directly with Yakima that this is the Base…

view full answer...

Answer 2

It is a lot of information. The best way to add a set of crossbars to mount the Yakima OffGrid Roof Cargo Basket item #Y07139-09 to the roof of your 2011 Ford F-250 crew cab is to use the roof rack by Yakima which includes the following parts: Yakima…

view full answer...

Answer 3

In order to obtain the key number, you'll have to have a locksmith pick the lock (if it's locked), then use a #Y8007835 Yakima control key to remove the lock cylinder. On the outside of the cylinder, you'll find the lock number, as shown…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 10

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

How Many Crossbars Does a Yakima Fit Kit Work With

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching