Will Lippert Standard Baggage Door Latch Kit Replace TriMark

Question

Question:

Will this replace a trimark lock Part number 5058937 compartment lock?

asked by: Katrina F

0

Expert Reply:

Yes it will! I was able to find the dimensions of a TriMark baggage door lock, and they are the same 5 inch tall, 4-1/2 inch wide, and 1-1/2 inches deep, so you can use the Lippert latch kit you asked about:

- Lippert Standard Baggage Door Latch Kit # LC317649

This kit even comes with the screws needed for installation so you're set!

expert reply by: Kyle S

0

Answer 1

We do have a replacement option for you. I was able to locate the measurements of your lock using the numbers you provided. - 5" wide x 4-1/2" tall x 1-1/2" thick The Global Link RV Baggage Door Slam Latch #295-000015 has…

view full answer...

Answer 2

I went out to the warehouse to take a look at the Lippert Components Standard Baggage Door Latch Kit #LC317649 referenced in your question. I have included an image with the dimensions labeled that you can review. The latch measures 6-1/2 inches…

view full answer...

Answer 3

There are a couple ways to determine what kind of axle you have. If there aren't any part markings on the axle or anywhere else on the trailer frame that list your trailer axle specifications, you need to measure your spindle with a calipers…

view full answer...

Answer 4

I might have an option for you but I don't have a way to look up what entry door latch your motorhome uses as there is no sort of data or query for this. The most universal option we offer for motorhomes is the Bauer Products Motorhome Door…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 12

Hi Joe, I assume you are referencing an Equal-i-zer weight distribution since you have shank #EQ90-02-4700. I went ahead and read the owners manual for their systems and there is noting regarding adjusting the angle of the hitch ball. The hitch head…

view full answer...

Will Lippert Standard Baggage Door Latch Kit Replace TriMark

Product Page this Question was Asked From

Continue Researching