How Much Fender Clearance Does Curt 5th Wheel 7-Way Adapter Require

Question

Question:

For the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7 Long Item # C56070, What is the minimum fender depth required for the back side of the cable to make the 90 degree turn down to the connection point? Im trying to mount this as high as possible in the truck bed.

asked by: David S

0

Expert Reply:

I checked with Curt and the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7 Long Item # C56070 would require 7 inches of clearance on the inner side of the fender/bed wall to install.

expert reply by: Jameson C

0

Answer 1

Hi Matt, The Curt Custom Fifth Wheel Installation Kit for Toyota Tundra #C16468-204 has industry standard spacing (22" front to back) so any hitch with this ISR spacing will fit. To my knowledge each of the hitches you listed have industry…

view full answer...

Answer 2

Yes, you can use the Curt 5th wheel and gooseneck in-bed wiring harness #C56070 in a truck with a drop-in bed liner. You will need to cut a hole through the bed liner as well as the bed for installation. If you want you can make the bed liner hole…

view full answer...

Answer 3

If your 2018 Toyota Tundra has the 6-1/2 foot bed, I recommend the Curt Custom Fifth Wheel Installation Kit #C16468-204. This installation kit includes custom-fit brackets that are confirmed to fit your truck and will use existing holes in the…

view full answer...

Answer 4

Since you have a plastic bed liner in your 2012 GMC Sierra 2500HD you will have to trim the liner in the foot print of the bed rails in order to install the kit, #C16411-204, in the truck. Plastic bed liners do not provide a stable surface which is…

view full answer...

Answer 5

According to Curt you can use the Adapter #C51455 on your 2018 Toyota Tundra for one of their brake controllers like the Spectrum #C51170 which uses a control knob and colors that resemble other knobs that are in modern vehicles. When they installed…

view full answer...

Answer 6

Since you have a 7-way connector on the rear of your 2017 Tundra I recommend the Hopkins Endurance, part #41157. This harness is 10-ft long and plugs into your existing wiring. I have attached a link to an installation video for this harness you can…

view full answer...

Answer 7

If your 2009 Toyota Tundra came with the factory tow package, then it should have a 7-way round trailer connector attached to the bottom of the rear bumper to the left of the trailer hitch (see photo). I recommend looking at the back of your truck to…

view full answer...

Answer 8

The Hopkins Fifth Wheel Hitch Install Kit, part #HM43397 will work just fine with your 2008 Toyota Tundra and your Reese Fifth Wheel. This harness is long enough to reach into the bed, but not so long where you would have a lot of excess to bundle.…

view full answer...

Answer 9

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 10

You are correct, as far as tire and wheel combos that come pre-mounted with a load range D 225/75-15 radial tire on aluminum wheel that has a 5 on 4-1/2 bolt pattern, we don't have any. A larger selection can be found with the more common 6 on…

view full answer...

Answer 11

I checked with Casita and your 2019 Casita 17 Deluxe has a 3,500 lb axle torsion axle. Due to the design of torsion (Torflex) axles there isn't a way to install a shock kit on them.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Much Fender Clearance Does Curt 5th Wheel 7-Way Adapter Require

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching