Trailer Roof Vent With LED Light

Question

Question:

Is there any kind of add on led light ring for these?

asked by: MC

0

Expert Reply:

There isn't an LED kit for the Ventline Vanair Trailer Roof Vent w/ 12V Fan # VP-543SP but the MaxxFan Dome Plus Roof Vent w/ 12V Fan Item # MA00-03810W comes with an LED light in the bottom ring of the vent. This fan circulates air like a ceiling fan when your vent is closed and the integrated rain shield lets you open your vent in any weather.

expert reply by: Kevin C

0

Answer 1

The MaxxFan Dome Plus Roof Vent part #MA00-03810B is an exhaust fan so it can only pull air out. If you are looking for a vent fan that does both you'll have to go with the larger square style like the MaxxFan Plus Roof Vent part…

view full answer...

Answer 2

The MaxxFan Dome Plus Roof Vent w/ 12V Fan - LED Light #MA00-03810B measures 8.51" wide, has a roof cutout of 6.25" and is 2.93" tall when closed. Attached is a review vide and a diagram depicting these measurements.

view full answer...

Answer 3

The lid of the MaxxAir Dome Vent part #MA00-3810B is not transparent. It would stick down from the ceiling it is installed on 3.08 inches when you have the vent closed and 2.14 inches when the vent is open. We can't recommend a way to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...