4-Way Trailer Wiring Harness that Fits 1995 Ford F-150

Question

Question:

This is the connector I have on my Ford pkp. see photos it appears different than what i am seeing here want to make sure I get one that works

asked by: Rusty H

0

Expert Reply:

Thanks for the picture of the connector you found on your 1995 Ford F-150. Based on that we know that the T-One harness part # 118316 that you referenced is a confirmed fit.

I attached an install video for this for you to check out as well.

expert reply by: Jameson C

0

Connector
(click to enlarge)

Answer 1

The process to install a 7-way and trailer brake controller on your 1997 Ford F-350 is not very involved. For a 7-way, you can use the Adapter 4-Pole to 7-Pole and 4-Pole part #37185 as long as you already have a 4-way like the T-One Vehicle Wiring…

view full answer...

Answer 2

For a 4-way harness confirmed as a fit for your 1995 Ford F-350 we have the #118316 which plugs in line with the taillight harness of your truck. It will operate independently of your truck's factory trailer wiring. If your current 7-way at the…

view full answer...

Answer 3

Installing a 7-Way and 4-Way combination trailer connector, like part #HM40975-11998, that you referenced, on your 1995 Ford F-350 is fairly easy, but for these trucks there are 2 different wiring situations if you do not have a factory 7-way trailer…

view full answer...

Answer 4

To change your 7-way round pin connector on your vehicle to a 7-way blade connector the wire connections are different. The best way to connect the wires on your vehicle to the 7-way blade connector is to use a circuit tester like part #PTW2993, and…

view full answer...

Answer 5

The Tow Ready T-One Vehicle Wiring Harness, part #118316 is indeed the correct harness for your 1995 F150. The harness will plug inline with the connector located along the frame rail on the drivers side just behind the rear wheel. You will find a…

view full answer...

Answer 6

For a 7-Pole connection you will need first install #118316 on your 1995 Ford F-150. I have included a video that shows this harness being installed on a similar vehicle. Then, I recommend using Adapter 4-Pole to 7-Pole and 4-Pole, #37185, because it…

view full answer...

Answer 7

The Curt Class IV Trailer Hitch Receiver, #14001, is just one of the hitch receivers that has been specially designed to fit a 1993 Ford F150 with a standard or step bumper. This fully welded trailer hitch receiver bolts onto the F150's frame…

view full answer...

Answer 8

I looked up the trailer connector wiring diagram for a 2007 Ford F-250 which should be the same as a Ford F-350 and found the 7-way trailer connector to contain the following wires: Orange = 12 Volt Power White = Ground Black/Green = Reverse Blue =…

view full answer...

Answer 9

We have many different hitches compatible with your truck. The best choice for you will depend on what you're wanting to tow. For lighter duty towing, I'd recommend the Class III hitch, part #75038. The hitch has a 5000 lb towing/500 lb…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

4-Way Trailer Wiring Harness that Fits 1995 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching