Brake Controller Installation on 2001 Toyota Sequoia
Question:
This SUV has never been used for towing and now I want to use it to tow a pop up camper about 4000 pounds in weight. The SUV came prewired with a 4 pin factory installed wiring harness. This would all be OK but for the fact that this wiring does NOT include the wiring necessary for the electrical brake connection which is necessary to provide synchronized braking power to the trailer wheels. The question is what should I do : 1. Is there some 4pin to 7pin adapter that may save the day : if so end of problem 2. should I run an additional similar wiring harness from the battery to the back of the SUV thru the firewall etc just to enable the trailer braking ? 3. OR should I totally replace the existing 4pin harness with the latest 7pin harness that provides for both brake lighting and braking ? Please provide the recommended kit along with your solution. Thanks.
asked by: Philip C
Expert Reply:
In order for the brakes on your pop up trailer to function, you will need to install a brake controller.
I would recommend a proportional brake controller like the Tekonsha Prodigy P2, part # 90885. A proportional controller will determine how quickly the tow vehicle is braking, and provide the proper voltage to the trailer brakes so that both vehicles stop at the same rate.
To install the controller, we offer a Brake Controller Installation Kit, part # ETBC7 which includes an adapter which will convert your 4-way connector to a 7-way. The Install Kit contains everything else you will need to complete your installation.
The 7-way has three additional wires that you would need to connect. The black wire, which is used to provide 12 volt accessory power to the trailer would run to the positive battery terminal by way of a 40 amp Circuit Breaker that is included with the kit. The purple wire is typically used when the trailer has reverse lights. If this circuit is needed, it would tap into the reverse light circuit on the tow vehicle which is accessible behind the taillight assembly. The blue wire would run to the passenger compartment and connect to the blue brake output wire on the brake controller. Once the controller is mounted under the dash following the manufacturer's instructions, the red controller wire would attach to the brake stoplight switch located at the top of the brake pedal. The switch can have several wires coming out of it, you will need to use a circuit tester such as part # PTW2993 and probe the wires exiting the switch until you locate the wire that only shows current when the brake pedal is pressed. Once the correct wire is located, tap that red brake controller wire into it. The black wire on the controller provides power to the brake controller. This wire would need to run to the positive battery terminal, using the proper circuit breaker (20 or 30 amp, depending on which brake controller you use). The necessary breaker is also included with the kit. The white brake controller wire provides the ground connection and would run to the negative battery terminal.
Products Referenced in This Question
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Shop: Front Mount Hitch
- Shop: Suspension Enhancement
- Shop: Mud Flaps
- Shop: Vehicle Tow Bar Wiring
- Shop: Hook Probe Circuit Tester
- Shop: Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle
- Article: Trailer Wiring Diagrams
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer brake controller
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: brake controller
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Search Results: trailer hitch
- Article: My Trailer Hitch Doesn't Fit
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Search Results: hitch
- Search Results: etbc7
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
on Trailer Wiring
