Suction Cup Mounts to Use with Camco Gen-Turi RV Generator Exhaust System

Question

Question:

in the video it shows a pair of suction cups that are used to hold the straps to the body. In the picture of the item, those are not shown???? Thanks

asked by: Brent H

0

Expert Reply:

In the review video for the Camco Gen-Turi RV Generator Exhaust System # CAM44461 that you mentioned our installer points out that she is using the Camco Gen-Turi Suction Cup Mounts # CAM44850. These are not included so you'd to order those separately.

expert reply by: Jameson C

0

Answer 1

The space that is between the outer wall of your coach and the exhaust pipe is going to depend on where your generator is and where the exhaust pipe you're connecting to is located. I can tell you that the 90 degree pipe on the bottom of the…

view full answer...

Answer 2

In order to install the Camco Gen-Turi RV Generator Exhaust System part #CAM44461 on a motorhome where the exhaust pipe is turned down towards the ground you'll need to cut that section of the exhaust pipe off. Once this is done, you can use the…

view full answer...

Answer 3

What you could do is use the 30 inch, 90 degree adapter for the Gen-Turi part #CAM44812 with the Gen-Ture part #CAM44461 to route the exhaust around the slide out.

view full answer...

Answer 4

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 7

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 8

If you check out the picture I attached you can see that the roller and slide out awning assembly of the Solera RV Slide-Out Awning #LCV000435661 actually will sit below the awning rail so your setup having a tight clearance between the rail and the…

view full answer...

Answer 9

We have toppers that'll work for 2 of your 3 sliders. For your 12 foot 9-1/2 slide, use #LCV000168109 which is designed for slides measuring between 152-157 inches wide. The longest topper we offer is for slides 188-193-3/4 inches, so…

view full answer...

Answer 10

I recommend to use the Solera 16-1/2' Slider part #LCV000435661 which matches the boxes width exactly so you will not have side overhang like we normally recommend but it is the biggest slide topper available to fit the 198" width of your…

view full answer...

Answer 11

According to Solara (Lippert), the correct number of turns to set the proper tension of their slide toppers like #LCV000163285 is between 12 to 16 turns, so I'd consider 14 to be a pretty good happy medium.

view full answer...

Answer 12

You sure can! You'll just need to know the brand and model of your slide out awning. For example the Solera Slide out awning #LCV000168109 uses replacement fabric #LCV000442075. We only sell fabric for Solera awnings at this time (3/15/2023) so…

view full answer...

Suction Cup Mounts to Use with Camco Gen-Turi RV Generator Exhaust System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching