Thread Size For Replacement Non-Locking Knob P1041

Question

Question:

what is the knob thread size ,1/2 in

asked by: Ray B

0

Expert Reply:

The Replacement Non-Locking Knob for Swagman Original and XP Series Bike Carriers - 2009 and Newer # P1041 accepts a M10 x 1.50 threaded bolt.

expert reply by: Kyle S

0

Answer 1

The only way to gt the ed cap with the strap is to get the full replacement they are available for right or left side depending on which one has gone missing the Replacement Wheel Loop for SportRack Wheel-Mounted Bike Racks Left Side is part…

view full answer...

Answer 2

I looked through a lot of knobs and was able to find replacement knob #P1041 which accepts an M10 x 1.5 bolt. I do not know what your application is but I can tell you that the knob is for Swagman Original or XP bike racks from 2009 to present. It…

view full answer...

Answer 3

You'll need one of the following knobs based on when your Swagman Original Bike Rack, part #S64152-2 was made: Prior to 2009, part #P1004, this includes a standard 2 inch bolt that will fit the knob. 2009 to Present, part #P1041, which is…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Thread Size For Replacement Non-Locking Knob P1041

Product Page this Question was Asked From

Continue Researching