M10 x 1.5 Knob to Fit an M10 x 1.5 Bolt

Question

Question:

Looking for a knob/nut to go on this M10-1.5mmpitch T-bolt. Please advise. Everything seems to be M8-1.25mm.

asked by: Will A

0

Expert Reply:

I looked through a lot of knobs and was able to find replacement knob # P1041 which accepts an M10 x 1.5 bolt. I do not know what your application is but I can tell you that the knob is for Swagman Original or XP bike racks from 2009 to present. It has not been tested with the Thule bolt # 853-5648.

expert reply by: Michael H

0

Answer 1

The only way to gt the ed cap with the strap is to get the full replacement they are available for right or left side depending on which one has gone missing the Replacement Wheel Loop for SportRack Wheel-Mounted Bike Racks Left Side is part…

view full answer...

Answer 2

The Replacement Non-Locking Knob for Swagman Original and XP Series Bike Carriers - 2009 and Newer #P1041 accepts a M10 x 1.50 threaded bolt.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

M10 x 1.5 Knob to Fit an M10 x 1.5 Bolt

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching