Can the Brightness On the Curt TriFlex Trailer Brake Controller Be Adjusted

Question

Question:

How can I make the display brighter on my curt C24VV?

asked by: Walt T

0

Expert Reply:

The brightness on the Curt TriFlex Trailer Brake Controller part # C24VV is not adjustable. This is the case for most LED display brake controllers. The Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 has an LCD display which is adjustable.

expert reply by: Conner L

0

Answer 1

On the Curt TriFlex Trailer Brake Controller part #C24VV there are two adjustments to be made. The first is the silver wheel on top this adjust the output of the controller. The second is on the left side of the controller it is a small slide. You…

view full answer...

Answer 2

I have attached for you below an excerpt from the manual on the Curt TriFlex Trailer Brake Controller part #C24VV which goes over the brightness settings. Please let me know if you have any other questions. "Slowly tilt the front of the TriFlex…

view full answer...

Answer 3

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 2, part #SC37VR will fit the jack feet of your 2022 Tiffin Allegro Buss. These pads measure 14" long X 12". Your jack feet should have…

view full answer...

Answer 7

The key here is that the functions are in the correct locations. Wire color is going to vary from manufacturer to manufacturer which is why you should always wire by function and use a circuit tester like #PTW2992 or #PTW 2993 when wiring in a…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck hitch.…

view full answer...

Answer 10

The SnapPad Prime Jack Pads #SP84FR4 are specifically designed to fit the Power Gear Leveling Systems w/ 10" Round Concave Jack Feet on your 2014 Fleetwood Bounder 34B. The Pads #SC99MR Stromberg told you to use will not fit on your Bounder as…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Hey Brad, thanks a bunch for going ahead and getting all those measurements in advance. Based on the measurements you've given, the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step #TL52SR will work perfect for your coach. These steps…

view full answer...