Tool Needed to Drive Hex Drive of Dutton-Lainson Hand Winch # DL11001

Question

Question:

The description describes that the loop drive can be driven with a power drill. Is there a recommended adapter for the drill?

asked by: Brian H

0

Expert Reply:

To drive the hex drive of the Dutton-Lainson Hand Winch # DL11001 does not require a special tool to do so. What you need is just a 5/8 socket which you most likely already have and you'd be set.

expert reply by: Jameson C

0

Answer 1

No, there is no minimum amount of weight required for worm gear winches such as #DL11001. I have linked a video review of this winch for you.

view full answer...

Answer 2

If you are wanting to use a drill to ease operation of the winch, the Dutton-Lainson #DL11011 would be a much better choice. This winch is specifically designed so that the handle is easily removable for use with a drill. Using the shaft directly…

view full answer...

Answer 3

While you certainly could use a worm gear winch such as #DL11001, I recommend using the Dutton-Lainson Hand Winch #DL10976, which is designed for what you are trying to do. This winch can be mounted to your ceiling and you can use Hex Shaft…

view full answer...

Answer 4

I do have a solution for you, however the Dutton-Lainson Hand Winch #DL11004 referenced in your question is actually designed for use with a polyester strap and not cable. For the Dutton-Lainson 2,000 pound hex gear hand winch that uses cable you…

view full answer...

Answer 5

You may be able to use the Dutton-Lainson Hand Winch - Worm Gear - Hex Drive - 2,000 lbs #DL11004 you were looking at to load your 3500lb boat on your boat trailer, but it will come down to how long the winch distance is, and if your trailer has…

view full answer...

Answer 6

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part #DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out.

view full answer...

Answer 7

The dimensions for the Dutton-Lainson Worm Gear Hand Winch #DL11001 are as follows: Height including hand crank: 12-1/4 inches Length of side panel: 5-1/2 inches Height of side panel: 4-1/4 inches Width of base: 4-3/4 inches

view full answer...

Answer 8

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part #DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out. For a 50 foot cable…

view full answer...

Answer 9

Yes, you will want part #DL205246, which is the replacement pin for the Dutton-Lainson worm gear winch #DL11001.

view full answer...

Answer 10

The Dutton-Lainson Worm Gear Winch, #DL11001, is just the winch you are looking for. A worm gear winch is great for smooth controlled raising and lowering and the reel will automatically stop when you stop cranking, whether you are lowering or…

view full answer...

Answer 11

The size winch that you will need depends on a couple of different factors. I have included part of our hand winch FAQ below regarding boat winches and have linked the FAQ article for you to view. Finding the Right Capacity Winch for your Boat…

view full answer...

Answer 12

That's weird, the 7-Way Vehicle Power Adapter for Furrion RV Observation Camera #FR87PR should allow you to use your camper at the same time as that's what it's designed for. If you want to just avoid the adapter all together,…

view full answer...

Tool Needed to Drive Hex Drive of Dutton-Lainson Hand Winch # DL11001

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching