Availability of Replacement Pin for Dutton-Lainson Worm Gear Winch

Question

Question:

HI, I have a Dutton-Lainson DL11001 winch and I seem to have broken the shear pin on the worm gear. Do you sell replacements?

asked by: Jon

1

Helpful Expert Reply:

Yes, you will want part # DL205246, which is the replacement pin for the Dutton-Lainson worm gear winch # DL11001.

expert reply by: Chris O

1

Answer 1

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part #DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out.

view full answer...

Answer 2

You may be able to use the Dutton-Lainson Hand Winch - Worm Gear - Hex Drive - 2,000 lbs #DL11004 you were looking at to load your 3500lb boat on your boat trailer, but it will come down to how long the winch distance is, and if your trailer has…

view full answer...

Answer 3

The Dutton-Lainson Hand Winch - Worm Gear - Hex Drive - 2,000 lbs #DL11004 accepts a 2" wide x 20' long winch strap which is sold separately. For a winch strap that fits this hand winch, I recommend the Hand Winch Strap with Safety…

view full answer...

Answer 4

For a trailer winch that can have a power drill attached to it so that it can be powered in or out you'd need a worm gear winch like the part #DL11001. Then for a 50 foot long winch cable the part #DL24104 would be a great option as well.

view full answer...

Answer 5

While you certainly could use a worm gear winch such as #DL11001, I recommend using the Dutton-Lainson Hand Winch #DL10976, which is designed for what you are trying to do. This winch can be mounted to your ceiling and you can use Hex Shaft…

view full answer...

Answer 6

To drive the hex drive of the Dutton-Lainson Hand Winch #DL11001 does not require a special tool to do so. What you need is just a 5/8 socket which you most likely already have and you'd be set.

view full answer...

Answer 7

Dutton-Lainson Hand Winch #DL15721 does not have a hex head that is fixed and would allow you to use an electric drill attachment. For that I recommend using worm gear winch #DL11001 which does have a hex drive and you can use a 5/8 inch socket…

view full answer...

Answer 8

The Dutton-Lainson Hand Winch #DL11004 that you referenced is only designed to handle straps like the 20 foot long #DL24242. It should not be used with synthetic rope like 6mm #BDW20095. There aren't any Dutton-Lainson hand winches that can be…

view full answer...

Answer 9

No, there is no minimum amount of weight required for worm gear winches such as #DL11001. I have linked a video review of this winch for you.

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Availability of Replacement Pin for Dutton-Lainson Worm Gear Winch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching